Litter robot timing light flashing4/3/2023 Have a look at this video: Īlso, there are two connection metal pins between the base and bonnet. If that is working fine, then the problem is probably with the connection between the base and the bonnet. Make sure the wires are well connected to the circuit. Activate the cat sensor by pressing on the globe just above the entrance in a forward and down motion. Litter-Robot III How To Fix Blinking Flashing RED Light, Diagnose, Repair & Replace LR3 Cat Sensor. Yellow light turns off, blue light remains lit. Inside the bonnet, you will see 2 wires connected to a small circuit. Press and hold Cycle button for 5 seconds. It is possible that the night-light is not even working, in this case, please remove the power from the robot and unclip the bonnet. ![]() If the night light turns on and the cycle is interrupted, then your bonnet needs to be replaced. One of the lights will start flashing, indicating the current Wait Time Setting. Press and hold the Empty button for about 5 seconds to enter Wait Time Setting mode. Then turn the unit onif the problem persists, try the Litter-Robot 3 Troubleshooter or contact Whisker Support. Extend the Wait Time when using a lower quality clumping litter that needs more time to set up. Reassemble the unit and verify a proper litter level. ![]() Turn the unit off and remove the bonnet and globe. Cover the light sensor which is located under the power button. Flashing yellow to red means the motor has detected an obstruction or jam. ![]() Please test if the night light is interrupting your cycle. Plug the unit back in and allow it to complete its cleaning cycle. Before troubleshooting, it’s advisable to: Unplug your power supply and then wait for 10 seconds. Here are recommended steps for adjusting the Cat Sensor: 1. This problem can be easily fixed by simply adjusting the Cat Sensor. If only the yellow light is on, it means that the Litter-Robot is cycling. If the Cat Sensor is triggered continuously for more than 2 minutes then the red light starts to blink. Elseys, are heavier than others so wed suggest keeping. Remove the tape from the Hall Effect sensor. Disconnect the 2 connectors of the motor and remove it. Carefully disconnect the 3 connectors on the motherboard and remove them. You should now see the motor, circuit board and Hall Effect sensors. Whenever the blue and yellow lights are on, it means that your Litter-Robot is in 8 Hour Sleep Mode. Make sure the litter level is at, or even a little below, the raised fill line. Step 2: Locate the circuit board and sensors. cutting-edge access solutions, including a 7-day timer, 00 at Amazon. The slowly blinking yellow light is related to the bonnet and its connection with the base. In terms of issues that may occur with your Litter-Robot 3, you may also see the blue light blinking. If the blue light flashes, it means the Waste Drawer is almost full and the waste needs to be removed. Litter-Robot 3 lights flashing sequentially Flashing yellow to red means the. Please provide us with your order number or a copy of the invoice. However, not all issues are covered in the official guide.We are sorry to hear that you are having trouble with your Litter-Robot. Check the waste port opening in the Globe for any clumps or objects stuck in or around the waste port opening. The LEDs show the status of the robot and help a user troubleshoot issues. If the blue light is still blinking, let's proceed with troubleshooting: STEP 1: Let’s check for any obstructions: -Unplug the power from the Base of your Litter-Robot. There are also four buttons which are "power", "cycle", "empty" and "reset". ![]() Aside from the main power light, there are three lights on the Litter Robot 3 control panel, which are blue (ready button), yellow (cycling button) and red (timing button). The Litter Robot 3 control panel provides the main user input /(buttons) and output (LEDs) for the robot. Customers often search online for a solution before contacting technical support, so this guide is intended to cover the most common situations. There's a lot of dust and debris which can cause issues, which leads to the robot not operating correctly. It is subjected to conditions which most robots - if they had a choice, would prefer not to be subjected to. The Litter Robot 3 is an incredibly popular automatic cat litter box which automatically detects when a cat has entered and exited, and rotates the main globe to sift and dump the used litter.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |